3A health · Equipment planning guide · Updated 21 October 2026
Compare biohacking equipment by function and installation needs
When sourcing biohacking equipment for a wellness center, begin with a list of the hardware functions, users, room conditions and documents you need. The 3A health range on this website includes mild hyperbaric chambers, light-wave vitality cabins and diffused oxygen equipment. Each family needs its own specification and installation review.
A chamber pressure value, an LED wavelength and an oxygen outlet flow describe different parts of a system. Keep every figure attached to its model and measurement point when comparing suppliers. A broad equipment label does not replace the configuration sheet.
Three equipment families to compare
| Equipment family | Questions for your specification | 3A health reference |
|---|---|---|
| Mild hyperbaric chamber | Confirm occupancy, cabin layout, pressure reference, external equipment and delivery access. | Chamber model range |
| Light-wave vitality cabin | Separate LED, heating and oxygen-system specifications; check the complete electrical load. | ORNF-1012 single-person cabin |
| Diffused oxygen system | Compare generator outlet flow, control terminal, piping scope and installation conditions. | SAMO-1010Hi 10L oxygen concentrator |
For chamber selection, start with the layout, specifications and quotation guide. Use the ATA, kPa and MPa guide to distinguish absolute and gauge pressure; its worked examples do not establish the operating settings of a product.
Read the actual model data
SAMO-1010Hi: a 10L oxygen concentrator for diffused-oxygen projects
The listed SAMO-1010Hi main-unit output is 10 L/min at 93% ±3% oxygen concentration. Its stated weight is 37 kg and its supply is 220 V / 50 Hz. These figures describe the listed unit; outlet concentration is not the oxygen concentration throughout a room.
The product page also shows a SAMO-T300 indoor control terminal with separate electrical and environmental specifications. Request an itemized quotation identifying the main unit, controller, sensors, wiring, piping, installation work and any exclusions. See the SAMO-1010Hi specification page and other diffused oxygen concentrator capacities.
ORNF-1012: separate light, heating and oxygen functions
ORNF-1012 is listed as a single-person light-wave vitality cabin with 75 LEDs at 660 nm and 75 at 880 nm, mica-panel heating and a separately specified oxygen system. The listed overall size is 1000 × 1200 × 2000 mm, total input power is 2400 W, and supply is 220 V / 50 Hz. Request the layout drawing to confirm dimension orientation and installation clearances.
When comparing an energy chamber or red light therapy listing, ask for the installed light source and the optical measurements needed for your project. The ORNF-1012 sheet identifies LED counts and wavelengths; it does not state irradiance at the user position or delivered light dose. Total cabin input power is not LED optical output. This model is identified as non-medical equipment. Review the ORNF-1012 model page rather than assuming that similarly named systems have identical functions.
Check the site before requesting the final quotation
- Room and occupancy: send the intended number of users and a dimensioned room plan. Include space for the cabin, external equipment, controls and maintenance access.
- Delivery route: record doorway, lift and corridor clearances, turning points and unloading conditions. Request packaged dimensions and weights for the quoted configuration.
- Electrical supply: state the actual site voltage, frequency and connection arrangements. For a US project, do not assume the listed 220 V / 50 Hz version matches the available supply; ask for written confirmation of the offered configuration.
- Installation scope: agree who supplies and installs the piping, cables, ventilation and accessories. Separate included work from work assigned to your local installer.
- Documents and support: request the model revision, equipment list, layout drawing, operating manual, maintenance requirements, warranty terms and the documents applicable to the intended installation.
The chamber site-planning checklist provides a more detailed starting point for chamber access, room planning and equipment coordination.
Common procurement questions
Which biohacking equipment should I compare first?
Start with the equipment function your project requires and the space you can allocate. Compare a named cabin or generator configuration against that requirement, then review the full installation and support scope. This guide covers the oxygen and light-cabin families listed here; it does not establish the capabilities of other technologies sold under the same broad label.
How can I compare quotations fairly?
Use the same occupancy, destination, site supply and inclusion list for each quotation. Ask every supplier to identify the exact model, unit of measurement, test conditions where relevant, supplied accessories and installation responsibilities. A lower equipment-only price cannot be compared directly with a quotation that includes additional equipment or work.
Request a model-specific equipment plan
Send 3A health your preferred models, quantity, destination city, room and access dimensions, available electrical supply and requested installation scope. Ask for a configuration list and itemized quotation that you can compare with the specification sheets. Contact 3A health about your project.
Product data and scope
Model figures above follow the linked 3A health product pages checked on 21 October 2026. Confirm the current revision and supplied configuration before ordering. This article supports equipment comparison and procurement; it does not provide a clinical protocol or establish a treatment outcome.
Cover: a company-showroom frame from the 3A health company-tour video. The display scene does not define the configuration of every model discussed here.
